BioVector's BL21(DE3) E.coli strain/Competent cells大肠杆菌菌株/感受态细胞 BioVector NTCC质粒载体菌种细胞基因保藏中心
- 价 格：¥9865
- 货 号：BL21(DE3) 电转
- 产 地：北京
- BioVector NTCC典型培养物保藏中心
- 联系人：Dr.Xu, Biovector NTCC Inc.
电话：400-800-2947 工作QQ:1843439339 (微信同号)
邮件：Biovector@163.com
手机：18901268599
地址：北京
- 已注册
BioVector's BL21(DE3) E.coli strain/Competent cells大肠杆菌菌株/感受态细胞
非毒性蛋白的高水平表达，可同时用于pET系列，pGEX，pMAL等质粒的蛋白表达；产品规格 BioVector's BL21(DE3) competent cells： 100μl/支BioVector's pUC19 (control vector，10pg/μl): 10μl保存条件(保质期)： -80℃（6个月） 基因型F- ompT hsdSB(rB- mB- ) gal dcm(DE3)产品说明BioVector's BL21(DE3)菌株用于高效表达克隆于含有噬菌体T7启动子的表达载体(如BioVector's pET系列)的基因。λ噬菌体DE3区含有T7噬菌体RNA聚合酶，该区整合于BL21的染色体上，所以称为BL21(DE3)。可同时表达T7 RNA聚合酶和大肠杆菌RNA聚合酶，用于BioVector's pET系列，BioVector's pGEX，BioVector's pMAL等质粒的蛋白表达。BioVector's BL21(DE3)感受态细胞由特殊工艺制作，pUC19质粒检测转化效率达10^7cfu/μg DNA。操作方法1.BioVector's BL21(DE3)感受态细胞从-80℃拿出，迅速插入冰中，5分钟后待菌块融化，加入目的DNA（质粒或连接产物）并用手拨打EP管底轻轻混匀(避免用枪吸打)，冰中静置25分钟。2.42℃水浴热激45秒，迅速放回冰上并静置2分钟，晃动会降低转化效率。3.向离心管中加入700μl不含抗生素的无菌培养基(2YT或LB)，混匀后37℃，200rpm复苏60分钟。4.5000rpm离心一分钟收菌，留取100μl左右上清轻轻吹打重悬菌块并涂布到含相应抗生素的2YT或LB培养基上。5.将平板倒置放于37℃培养箱过夜培养。Sample Induction Protocol (for reference only)1. Inoculate a single colony from a freshly streaked plate into 5 ml of LB medium containing the appropriate antibiotic for the plasmid and host strain.2. Incubate with shaking at 200 rpm at 37℃ overnight. 3. Inoculate 50 ml of LB medium containing the appropriate antibiotic with 0.5 ml of the overnight culture prepared in step 2(use the 500 ml triangular flask as the container would be better).4. Incubate with shaking at 150 rpm at 37℃ until the OD 600 reaches 0.5-0.8.5. (Optional)Pipet 1ml of the cultures into clean microcentrifuge tubes and place the tubes on ice until needed for gel analysis or storage at -20℃. These will serve as the non-induced control samples. 6. Add IPTG to a final concentration of 1 mM. Optimal time for induction of the target protein may vary from 2-16 hours, depending on the protein.7. Incubate with shaking at 120 rpm at 37℃ for 3-4 hours. To determine the optimal time for induction of the target protein, it is recommended that a time course experiment be performed varying the induction from 2-16 hours.8. Place the culture on ice for 10 minutes. Harvest cells by centrifugation at 5,000×g for 10 min at 4℃.9. Remove the supernatant and store the cell pellet at -20℃ (storage at lower temperatures is also acceptable). IPTGPrepare a 1 M solution of IPTG (Isopropyl-β-D-thiogalactoside; Isopropyl-β-D-thiogalactopyranoside) bydissolving 2.38 g of IPTG in dd water and adjust the final volume to 10 ml. Filter sterilize before use. 注意事项1. 感受态细胞最好在冰中缓慢融化，插入冰中8分钟内加入目标DNA，不可在冰中放置时间过长，长时间存放会降低转化效率。2. 混入质粒时应轻柔操作。3. 转化高浓度的质粒可相应减少最终用于涂板的菌量。4. 诱导时，IPTG浓度可选（0.1-2mM均可）。5. 为获得需要量的蛋白，最佳诱导时间，温度，IPTG浓度需实验者优化。
Supplier来源:BioVector NTCC Inc.
TEL电话:400-800-2947
Website网址: http://www.biovector.net
非毒性蛋白的高水平表达，可同时用于pET系列，pGEX，pMAL等质粒的蛋白表达；产品规格 BioVector's BL21(DE3) competent cells： 100μl/支BioVector's pUC19 (control vector，10pg/μl): 10μl保存条件(保质期)： -80℃（6个月） 基因型F- ompT hsdSB(rB- mB- ) gal dcm(DE3)产品说明BioVector's BL21(DE3)菌株用于高效表达克隆于含有噬菌体T7启动子的表达载体(如BioVector's pET系列)的基因。λ噬菌体DE3区含有T7噬菌体RNA聚合酶，该区整合于BL21的染色体上，所以称为BL21(DE3)。可同时表达T7 RNA聚合酶和大肠杆菌RNA聚合酶，用于BioVector's pET系列，BioVector's pGEX，BioVector's pMAL等质粒的蛋白表达。BioVector's BL21(DE3)感受态细胞由特殊工艺制作，pUC19质粒检测转化效率达10^7cfu/μg DNA。操作方法1.BioVector's BL21(DE3)感受态细胞从-80℃拿出，迅速插入冰中，5分钟后待菌块融化，加入目的DNA（质粒或连接产物）并用手拨打EP管底轻轻混匀(避免用枪吸打)，冰中静置25分钟。2.42℃水浴热激45秒，迅速放回冰上并静置2分钟，晃动会降低转化效率。3.向离心管中加入700μl不含抗生素的无菌培养基(2YT或LB)，混匀后37℃，200rpm复苏60分钟。4.5000rpm离心一分钟收菌，留取100μl左右上清轻轻吹打重悬菌块并涂布到含相应抗生素的2YT或LB培养基上。5.将平板倒置放于37℃培养箱过夜培养。Sample Induction Protocol (for reference only)1. Inoculate a single colony from a freshly streaked plate into 5 ml of LB medium containing the appropriate antibiotic for the plasmid and host strain.2. Incubate with shaking at 200 rpm at 37℃ overnight. 3. Inoculate 50 ml of LB medium containing the appropriate antibiotic with 0.5 ml of the overnight culture prepared in step 2(use the 500 ml triangular flask as the container would be better).4. Incubate with shaking at 150 rpm at 37℃ until the OD 600 reaches 0.5-0.8.5. (Optional)Pipet 1ml of the cultures into clean microcentrifuge tubes and place the tubes on ice until needed for gel analysis or storage at -20℃. These will serve as the non-induced control samples. 6. Add IPTG to a final concentration of 1 mM. Optimal time for induction of the target protein may vary from 2-16 hours, depending on the protein.7. Incubate with shaking at 120 rpm at 37℃ for 3-4 hours. To determine the optimal time for induction of the target protein, it is recommended that a time course experiment be performed varying the induction from 2-16 hours.8. Place the culture on ice for 10 minutes. Harvest cells by centrifugation at 5,000×g for 10 min at 4℃.9. Remove the supernatant and store the cell pellet at -20℃ (storage at lower temperatures is also acceptable). IPTGPrepare a 1 M solution of IPTG (Isopropyl-β-D-thiogalactoside; Isopropyl-β-D-thiogalactopyranoside) bydissolving 2.38 g of IPTG in dd water and adjust the final volume to 10 ml. Filter sterilize before use. 注意事项1. 感受态细胞最好在冰中缓慢融化，插入冰中8分钟内加入目标DNA，不可在冰中放置时间过长，长时间存放会降低转化效率。2. 混入质粒时应轻柔操作。3. 转化高浓度的质粒可相应减少最终用于涂板的菌量。4. 诱导时，IPTG浓度可选（0.1-2mM均可）。5. 为获得需要量的蛋白，最佳诱导时间，温度，IPTG浓度需实验者优化。
Supplier来源:BioVector NTCC Inc.
TEL电话:400-800-2947
Website网址: http://www.biovector.net
- 公告/新闻
